5" ERW Steel Pipe Mill, 2" ~ 5.5" (48.6 ~ 139.8mm) Dia x .055" ~ .213" (1.4 ~ 5.4mm) t x 60 MPM (Used)
Specifications
| Year | 2004 |
| Condition | Used |
| Stock Number | VX-17603 |
Description
Year Manufactured: 2004
General Specifications:
Year Manufactured: 2004
Cap.: ¢ 5.5" (139.8mm) – 3.9" x 3.9" (100mm x 100mm)
1.9 ~ 5.5" (48.6~139.8mm) Dia x .055"~.213" (1.4mm ~ 5.4mm) t x 60 MPM
Pipe Dia.: ¢ 1.9" ~ 5.5" (48.6-¢ 139.8mm)
· 2" x 2" (50mm x 50mm)
· 3.9" x 3.9" (100mm x 100mm)
Wall Thickness:1.4t-5.4t mm
Pipe Length 4~14M
Line Speed: 10M~60m/min
1)Uncoiler
Type: Double Swivel Type
drum toggle linker jaw type
Cap.: Strip Width Max. 17.3 (440mm)
Coil Out Dia.: Max.: 70.9" (1,800 mm)
Coil in Dia.: Max.: 20" (508mm)
Coil Weight: Max.: 10 Ton x 2 ea
2) Pinch & Leveler
pinch roll up/down: Hyd. ¢ 3.2" x 3.9" (80 mm x100mm)
pinching speed: Approx 10m/min
pinching speed: Approx 10m/min
Pinch Roll: ¢ 150mm
width of pinch roll: Max. 500mm
side guide (R): Hyd. ¢ 50 x 40st
side guide (L): Hyd ¢ 50 x 85st
leveler roll dia: ¢ 100m
Width of roll: ¢ 500mm
3) Shear & End Welder
-General
coil width: Min 160mm - Max 440m
coil thickness: Min 1.4 – Max 5.4
joint method: MIG Welding Type
-Component
Side guide Range: Max. 500 mm – 2 Set
Width Adjusting: Manual Control
Clamping: 2 Hyd. ¢ 80 x 50st – 2 Set
Butt Move: 2 Hyd. ¢ 80 x 50 st – 2 Set
- Shear
Shearing: 2 Hyd. ¢ 140 x 250st
No. of Blade: 2 couple
Blade Material: SKD – 11(JIS)
- Exit Pinch Roll
Driver: 2.2kwx4px1/60 geared motor
Pusher: 2 Hyd. ¢ 63 x 65st
Roll Dia.: ¢ 150mm
Width of Roll: 500mm
- Mig Welder (SCR)
Current of Welder: 350 Amp
Input Gas: CO2 more than 99%
Wire: ¢ 1.2, ¢ 1.6 flux cord wire
- Welding Torch Transfer
Transfer Motor
4) Strip Accumulator
-General
Type: Double Winding
Strip width: Max. 440mm
Winding Capacity: 300m
Spiral drum Dia: ¢ 1,750mm
Out basket Dia : ¢ 3,280mm
-Component
Entry unit: Roll guide type
Guide Roll: ¢ 110mm x 3 set (Up/Botten)
Side Guide Roll: ¢ 64mm – 2 set
Water Nozzle: Auto close/open type
-Spiral Drum Unit
Drum roll: ¢ 69 x L500 x 20 ea.
Drum tilting angle: Max 10"
Upper guide roll: 2set
-Inner basket unit
Roll Size: ¢ 69 x L500 x 24 ea
Cushion Roll Size: ¢ 88 x L500
Side guide roll: ¢ 64 x 8 set
- Outer basket (winding drum)
Roll Size: ¢ 68 x L500 x 36 ea
Side Guide Roll: ¢ 64 x 9 Set
Drum Holding Roll: 8 Set
- Driving Motor
D.C. Motor Power: 37 kw
- Exit Unit
Upper/bottem Guide Roll: ¢ 110 x 4P
Side Guide Roll: ¢ 95 x 1 Set
- Control
Control Panel: Cubicle type
5) Forming Section
- Guide Roll
Upper Roll: ¢ 160 x w500mm
Lower Roll: ¢ 100 x w500mm
Roll Material: SKD – 11 (JIS)
Roller: ¢ 75 x H100mm – 2 Set
- Leveler
No. of Roll: 5 Roll
Roller: ¢ 70 x 500 mm
- Forming Stand (Breakdown)
Breakdown Section: BD1,2,3,4
Driven Roll Shafter: ¢ 90mm
Normal Roll Root Dia.: ¢ 160mm
Max. Speed of Lower Roll: 120 rpm
- Forming Cluster
Roll Shafter: ¢ 60mm
Roll Root Dia.: ¢ 140mm
- Fin Pass Stand
Fin Pass Section: FP 1,2,3
Roll Shafter: ¢ 90mm
Roll Root Dia.: ¢ 160mm
- Fin Pass Side Cluster
Roll Shafter: ¢ 60mm
Roll Root Dia.: ¢ 140mm
- Seam Guide
Roll Root Dia.: ¢ 140mm
- Driving Gear Box
- Type: Worm & Helical Gear
Coupling: Chain type
Gear Ratio
- D.C. Motor for Forming
D.C. Motor Power: 90kw
Output Revolution: Max. 2,100rpm
Basic Lower Speed: Min. 650 RPM
6) Welding Section
- Squeeze Roll Stand
Roll Shafter: ¢ 75mm
Roll Root Dia.: ¢ 130mm
construction
- H.F. Welder
H.F. Output Power: Max. 450kw
Control Unit: Thyrister (SCR) – 1 Set
Plate Transformer: 1 Set
Rectifier Section: 1 Set
Oscillator Section: 1 Set
H.F. Output Transformer: 1 Set
Control: 1 Set
- H.F. Welder & Emulsion Cooling Sys.
Main Pump: 5.5kw – double
Fan: 2.2kw – 2 ea.
Spray Pump: 1.5kw
- Bead Scarfing Unit
No. of cutting tool: 2 Unit
Cutter up/down: Hydro Cylinder
Tip Adjusting Range: 50mm
- Scrap winder
Drum Dia.: Min. 290mm – Max. 355mm
Expanding Method: Foot Pedal-Man.
Driving Power: 0.4kw – Max. 100 RPM
- Ironling Stand
- C/T Box Die
Adjusting Methos: Screw – Manual
Work Coil Up/Dow Adjust: 50 mm
Work Coil Right/Left Adjust: 50mm
Work Coil Front/Rear: 50mm
7) Cooling Box
Length: 4500mm
8) Sizing Section
- Sizing Stand
Sizing Section: S 1, 2, 3, 4
Roll Shafter: ¢ 90mm
Roll Root Dia. – Round: ¢ 160mm
Roll Root Dia. - S.Q. Tube: ¢ 320mm
- Sizing Side Cluster
Roll Shafter: ¢ 35mm
Up-down Moving Range: + 30mm
Left-Right Moving Range: + 30mm
Turning Range of Roll Holder: 360 deg.
- Measuring Roll
Roll Root Dia.: ¢ 127.324mm
Pulse Per Revolution: 5,000 pulse
Hysteresis: 0.08mm
Liner Length of Revolution: 400mm
Push: Air ¢ 40 x 30st
Touching Pressure: 3.5 bar
Touching Force: 44kg
- Driving Gear Box
Type: Worm & Helical Gear
Coupling: Chanin Type
Gear Ratio
- Change Gear Box
Type: 2 Stage Helical Gear Type
Coupling: Gear Coupling
- D.C. Motor for Sizing
D.C. Motor Power: 90kw
Output Revolution: Max. 2,100 RPM
Basic Lower Speed: Min. 650 RPM
Control Panel: Cubicle Type
9) Cut-Off Machine
Type: Flying Friction Saw
Cutter Travelling Length: 4,000mm
Travelling Device: NC Drive System
Maker: YASKAWA (Japan)
Drive Motor: AC 22kw x 1,500 RPM
Servo Motor
Drive Gear Ratio: 1/6.0
Saw Blade: ¢ 900 x 5t-7t
Saw Motor Power: AC 55kw x 4 Pole
Tolerance of Cutting Length: + 1mm
10) Double Dump Runout Table
Type: V Shape Roll Conveyor
Feeding Speed: Max. 120 m/min.
Motor Power: AC 7.5kw
Speed control: Eddy Current
Controlled VS Motor
Dumping: Rotary Kicker/Gear Motor
Table Length: 13,000mm
5” End Facing Machine
1) Inlet Chain Conveyor
Type: Flat Roller Chain Conveyor
Feeding Speed: 14m/min.
Table Length: 2,000mm
- Pushing
¢ 80 x 1000 Set Air Cylinder
Aligning Pusher
- Pushing:
¢ 160 x 300 Set Air Cylinder
¢ 80 x 300 Set Air Cylinder
Stacking & Bundling Lifter With Chain Conveyor
Chain Conveyor
Lifting Pocket: 5 Set
- Closing Arm:
¢ 40 x 170 Set Hyd. Cylinder
- Lifting Stroke Max. 680mm
- Lifting Drive: A.C. 3.7kw
Flat Roller Chain Conveyor
- Feeding Speed: 14m/min.
- Motor Power: A.C. 2.2kw x 4P
- Table Length: 197.2" (5,000mm)
- No. of Lane: 5 Lane